Search


Advanced search

Active participation in the Discussion Forum requires a currently paid membership to the MCA or one of its local Chapters. Contact your Board Members with questions.
Massey Talk Discuss Massey related topics, Q&A, mechanical problems, etc.
Massey Discussion Forums :: Massey Talk :: tractor design faults View modes: 
User avatar
Posted: 2/7/2013 2:05:47 PM
   

RE:tractor design faults

It has been quite a time since we had this thread out!  Surely some of you have been having some frustrations out in the sheds this winter??

So here I am again with a grump born out of very recent experience.  My MF 165 with Perkins 203 engine - my regular workhorse - had developed a leaky water pump and also a bit of oil was coming out of the front of the crankshaft.  So I thought best fix the two together.

What a performance!!  Come back Harry Ferguson with your simple tip up hood (bonnet!).  What a fiddle it is getting the hood and grill off. Tedious small screws round the dashboard and small studs everywhere in miserably poor accessible places.  OK when new I suppose but even then tedious - there must be 30 or so in all just to reveal the radiator.  The top of the hood - what they call the "coffin" in the trade is quite heavy and awkward on your own to lift off and subsequently get back on.  I believe that if you had a new tractor it would be impossible to get on and off without scratching paintwork.  Using the Grey Ferguson model let us recall that there were only two studs fixing the bonnet on at its swivel point and the same could easily have been designed into the 165.

The water pump was OK to get at once revealed.  However the crankshaft oil seal requires the bottom pulley to be pulled off.  Easy enough to undo with the tractor in gear but when you come to pull it back it will not clear the front subframe.  So the next job is to undo the 6 or is it 8? big studs and nuts and bolts so that you can shift it forward sufficiently for it to clear - a matter of only half an inch or so.  One has to undo them right to the last thread and jack up the belly of the tractor to take the weight off them, then lever it apart from the engine mountings - all highly precipitous with it hanging on by threads only!  Longer studs and bolts, or a more hollowed out sub frame would have removed the need for this performance.

Then having got the pulley off you would have thought that it would be possible to pick the seal out of the timing case.  But NO - you have to remove the timing case as the original one is retained in an imperceptibly thin collar (removable as we were to find out).  We did not realise there was a collar in there so back I went to the dealer to say that the supplied seal would not fit.  He scratched his head and was about to send a query to AGCO with a photo.  Then when he had finally got a splinter in his fingers from his head he decided first to consult with the fitters.  5 minutes later he came back from the workshop saying that in fact the collar was old design and had now been done away with! (of course no mentuion of this on the computer parts lists!). So the supplied seal was correct after all.  Got home and the collar punched out quite easily with a thin screw driver.  By now of course we needed a new timing cover gasket as it is so large that one needs a hell of a large sheet of gasket paper to make one.  Two days later this came into stock and we were on to reassembly and everything is now back together  - much to my 4 year old young garndson's relief!

I have just awoken from a snooze by the log fire so I felt I really must report my anguish to the world!!

Looking forward to hearing from some of you on your trials and tribulations.......

John




| | |
User avatar
Posted: 2/7/2013 7:09:15 PM
   

RE:tractor design faults

Well this is a stupid one but, I just hit it!!  Why in the world did they engineer the 22 with disk brakes then bury them in the axle housings so you have to take off the rear wheel, unbolt the and remove the axle housing to just look at them. A half day project just to get to one of them.  That does not include doing anything to the brakes themselves.

#$%^&*()_

GTE


| | |
User avatar
Posted: 2/7/2013 9:53:53 PM
   

RE:tractor design faults

Gary:

I think it is so you put new oil in the rear end every 50-60 years or so. Don't you just love that set up?? I thought the same thing a couple years ago when I had one apart.

Speaking of design faults, I tried to reply to your post on the Wallis Tractors thread and there is no reply button on the last two posts and Malcolm still can't get on here.....

Maybe it has someting to do with that Astroid that is about to hit us sometime next week??

Joe


| | |
User avatar
Posted: 4/20/2013 3:08:20 AM
   

RE:tractor design faults

I was tidying up in my workshop yesterday and quite coincidentally these two spanners fell together on the bench.  There is a story behind them.  They are both 11/16ths x 1 1/16ths.

As you will see the open end spanner is the classic Ferguson spanner that was supplied with all Ferguson tractors from the Ferguson Brown (with detail differences) onwards.  This open ender here is the one supplied new with my Dad's new Ferguson TEA 20 serial no. 39615  in June 1948 - and we still have the tractor.

As you will all know these spanners were designed to fit most of the nuts and bolts on the tractors and implements.  Well for the implements they were fine when the implement fine thread bolts were new but once they had corroded a bit and the heads worn they became the objects for cursing.  My Dad after a year or two got fed up with it and bought the ring spanner - what a POSITIVE difference it made.

There was sonly one such open ender supplied with each tractor so once the nuts got a bit tight you had to get another spanner to hold the bolt head.  That is FAULT No. 1 with them.

The wheel nuts are 1 1/16th but as the picture shows you cannot get a full grip on them because of the curvature of the wheel dish.  That is FAULT No. 2 with it.  As you can see the swan neck on the ring spanner solves this problem and gives full on positive grip.

So dare I say it - all was never perfect even in the iconic Ferguson camp!!!  There should have been two ring spanners supplied with every tractor.  Apparently even the Ferguson demonstrators of the day, who always kept there tractors and implements in as new clean condition, always carried a spare spanner to hold awkward nuts and bolts!

Incidentally AGCO is currently releasing (at least in the UK) a promotional reproduction of the spanner supplied with the TE 20 Fergusons here.  It's supposed to be available in the dealers next week.

John

Post attachments:
P1010020.jpgP1010021.jpg

| | |
User avatar
Posted: 4/9/2014 11:54:43 AM
   

RE:tractor design faults

It's some time since we had this particular thread up but I am prompted to do so again.  This afternoon I was tinkering with the tractors on odd jobs one of which was to clean the spark plugs on my red Pacemaker orchard.

Which light headed engineer made this tractor so that you have to remove the air cleaner to take out plug No. 3?  I ask you!!!

Since we last had this thread up some of you must have had snags with the repair and maintenance of your equipment - let's hear about them please.................

John 


| | |
1 2 3 4 5 6